top of page
DMX Accessories
Architectural control
PHAROS EXPERT
XPC 1 / XPC 2
EXPERT CONTROL
Benefit from Pharos expertise in dynamic architectural lighting with an all-new, practical, and straightforward control solution centred around a single, reliable set-and-forget controller. With DMX, DALI and a couple of convenient contact closures and relays all on board, Expert Control provides up to 1024 channels and is just the job for architectural lighting that requires the benefits of dynamic movement and colour in a cost-effective and user-friendly package. Expert Software helps and guides you through programming the controller. Also available is a companion 5” touchscreen; the elegant Expert Touch, and completing the range are two accessories: Expert Repeat which is a convenient DMX splitter for output distribution, and Expert Switch for PoE networking (see DMX Accessories for details and Specifications). With the reliability you expect from Pharos and our expertise in dynamic lighting in architecture and entertainment: an easy to install, easy to use control solution.
XPR
4-WAY SPLITTER
Expert Repeat is a convenient DMX512 splitter / repeater with four output ports compatible with the RDM standard to provide DMX distribution to luminaires. The incoming isolated DMX signal from your Expert Control is regenerated four times on isolated, self-healing ports for distribution to your fixtures. DMX splitters are an essential requirement for most control systems, allowing multiple separate cable runs from a single DMX output and ensuring electrical isolation. In the same size and look as Expert Control and Expert Switch, this DIN rail mount repeater with install-friendly connectors requires a power supply in the range of 9 to 48V DC.
XPS
EXPERT SWITCH
Expert Switch is a convenient unmanaged Ethernet switch providing simple power and networking solutions for up to four Power-overEthernet devices. An elegant and easy solution to connect and power Expert Control and three Expert Touch, with the Ethernet-in non-powered port connecting directly to the programming laptop or joining to a local network. In the same size and look as Expert Control and Expert Repeat, this DIN rail mount PoE network switch only requires a 24V DC power supply.
PHAROS DESIGNER
EDN
ETHERNET DATA NODE
The Pharos EDN (Ethernet Data Node) is a convenient and scalable solution, providing cost-effective Ethernetdistributed DMX ports for large control projects. The EDN is an easily configurable networking node that is specifically designed to add physical DMX ports to Pharos Designer Controllers and integrates natively with the full Pharos Designer range. Extremely compact, it packs up to 20 DMX512 output ports into a 1U 19” form factor. For higher port count installations, nodes can be daisy-chained to provide as many physical DMX ports as you need. EDNs are discoverable through Pharos Designer software and associated to a Controller to be seamlessly configured as part of your patch. Ports can be flexibly assigned to any Designer Controller in your project providing an elegant data distribution solution over an Ethernet network with minimal setup required.
RIO
REMOTE DEVICE (INPUT/OUTPUT)
The Pharos RIO 80, 44 and 08 devices provide a convenient and scalable way to add inputs and outputs to a Pharos system for show control and integration. Each device can be placed where it is needed and connected to the Controllers over an Ethernet network. Each RIO has a multi-protocol serial port, supporting DMX input and output, and a combination of multi-functional...
RIO A
REMOTE DEVICE (INPUT/OUTPUT AUDIO)
The Pharos RIO A device provides a convenient and scalable way to add audio integration to your Pharos system. The RIO A has an audio input, supporting linear timecode or up to 30 band spectrum analysis, as well as a MIDI input and output. Each device can be placed where it is needed and connected to the Controllers over an Ethernet network...
RIO D
REMOTE DEVICE (INPUT/OUTPUT AUDIO)
The Pharos RIO D device provides a convenient and scalable way to control DALI fixtures and ballasts from Pharos Controllers. Each RIO D supports a single DALI bus, which can be used as an output for control and as an input for triggering. Each device can be placed where it is needed and connected to a Pharos Controller over an Ethernet network. The RIO D is Power-over-Ethernet (PoE) powered, with a rugged DIN-rail mounting enclosure and install-friendly connectors. A DALI bus can support up to 64 devices, and the RIO D can also be used for ballast configuration and site commissioning. DALI Emergency ballasts are also supported, with the ability to schedule automatic Function and Duration tests...
BPS
WALL STATION - REMOTE DEVICE
The Pharos BPS is a versatile 8-button station with integrated button LEDs that works with any Pharos Controller. The stylish BPS is available in a range of finishes and there are two variants for compatibility with either US or UK back boxes. Install is easy and convenient as the BPS only requires a single Power-over-Ethernet (PoE) network connection...
ACCESSORIES
PATHWAY SPLITTERS
The Pathway DMX Repeater series of opto-splitters are an essential component of DMX distribution systems, permitting star-wiring configurations while isolating and protecting equipment from electrical faults. The Installation/Wall-mount DMX Repeaters are internally pre-wired in small or medium-sized NEMA1 enclosures, complete with a power supply and conduit knockouts for fast, east installation. The RDM model supports the bi-directional communication standard E1.20 Remote Device Management (RDM).
LD180
DMX512
LD180 is a constant voltage LED driver used as an interface for Moda Light RGB products. It has white light DMX dimming options due to its four channel controller. It is capable of being linked together with multiple LD180 devices hooked up to a network for larger DMX installations.
bottom of page